Can I Install a Bath Tub Myself? Considerations And Actions
Can I Install a Bath Tub Myself? Considerations And Actions
Blog Article
The writer is making several good points about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround as a whole in the content down below.
Installing a bath tub isn't exactly brain surgery, however it does call for solid plumbing, woodworking, and also often, tiling skills. Replacing an old bath tub with a new one is additionally a moderately hard project. If the old bathtub is readily obtainable, the project can relocate quickly; if you need to open a wall to get rid of the old tub and also position the brand-new bathtub, the job is a lot harder. In either situation, the task is within a home handyman's abilities, although you will need a helper to vacate the old tub as well as embeded in the new one. See to it you have certified yourself for the work and fit trying it. Rather than working with a contractor to take control of a halfway-completed task, it is better to think about using one before you start. Opportunities are you may need a specialist plumber to make tube links.
This short article will assist you mount a new tub in your shower room if you have actually already purchased a brand-new bathtub and don't need to transform the setup of your previous water supply pipes.
Your devices and also material checklist ought to consist of the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you should do is detach the water system. After doing so, switch on the taps to drain pipes any kind of water continuing to be in the system. The procedure of removing the existing taps can be rather problematic due to the restricted gain access to that is commonly the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a fabric prepared for the staying water that will certainly originate from the pipelines. When the supply pipelines have actually been eliminated, utilize the exact same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning throughout this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing substance.
Prior to going on to fit the brand-new faucets, contrast the pipe links on the old taps to the new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the new taps are plastic, then you will require a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end supplies a connection to the current supply pipes.
If you need to fit a monobloc, then you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin making sure that the washers remain in area between the tap and also the sink. Safeguard the tap in place with the supplier given backnut. When the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap adapters. The previous type should be attached to the faucet ends initially, tightening up only by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Bathtub
Utilizing the two wood boards under its feet, put the bathtub in the required placement. The wooden boards are useful in equally spreading the weight of the bath tub over the area of the boards rather than focusing all the weight onto 4 small factors.
The next objective is to guarantee that the tub is leveled all round. This can be accomplished by checking the level and readjusting the feet on the tub until the spirit level reviews level.
To mount taps, fit all-time low of the furthest adaptable tap adapter to the appropriate supply pipeline by making a compression join; after that do the exact same for the various other tap.
Activate the supply of water and also check all joints as well as brand-new pipework for leaks and also tighten them if required. Load the bathtub and additionally check the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, deal with the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub must wait till the bathtub has been made use of at least once as this will certainly resolve it into its last placement.
Preparing for the Setup
To start with, the supporting framework provided with the bathroom needs to be fitted (if called for) according to the manufacturer's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to see to it that if the faucet features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the faucets device to prevent strain on the tub.
Fit the versatile faucet adapters to the bottom of both taps making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet with the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you use every one of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath need to currently prepare to be fitted in its final placement.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the fitting can relocate sufficient to break a rigid seal, creating the water to pass through the wall surface between the bathroom as well as the tiling, resulting in complications with wetness as well as possible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your fixtures and fittings. They are sold in tubes and also cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of soaked paper or soft rope. Keep in mind to always fill the bath tub with water prior to sealing, to permit the motion experienced when the tub remains in use. The sealant can fracture relatively very early if you do not take into account this movement prior to securing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily readily available on the marketplace. It is recommended to fit the tiles using waterproof or water resistant adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed our topic about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks a ton for spending some time to browse our article post. Are you aware of somebody who is in the market for How to Install a Bathtub? Be sure share it. Many thanks for going through it.
Check Us Out
Report this page